Clutch Slave Cylinder/Throwout Bearing - Ford - Zetec/SVT/Duratec (MTX75) Manual 5 Speed

SKU: FSLSC304

by: LuK

  • $79.95
  • 7 reviews


Clutch Slave Cylinder/Throwout Bearing - Ford Focus Zetec/Duratec MTX75 Manual 5-Speed, and SVT 6-Speed

LuK clutch slave cylinders have a long operating life and low friction characteristics thanks to the special design of the central seal with a plastic reinforcement and the special lubricants used.

Hydraulic concentric slave cylinders
Concentric slave cylinders are fitted within the bell housing where the hydraulic cylinder encloses the input shaft. They are easy to fit and automatically adjust the travel of the diaphragm spring during clutch wear. The housings are manufactured almost exclusively from plastic resistant to high temperatures and now only rarely from aluminum. The integrated design where the guide tube and housing are injection molded as one part is particularly robust. A travel sensor can be fitted on the side of the housing in hybrid vehicles and automated clutch actuation systems. The release bearing can be equipped with a thrust washer to reduce friction or a cardan joint to prevent judder caused by geometrical defects.

Note: During assembly use silicone adhesive such as (Permatex Ultra Black Part#82180) or Ford equivalent on the backside mating surface of the slave cylinder where it meets the transmission.

Fitment:
Ford Focus DOHC Zetec 2.0L 2000 2001 2002 2003 2004
Ford Focus SVT  2.0L  2002 2003 2004
Ford Focus Duratec 2.3L 2003 2004
Ford Focus Duratec 2.0L 2005 2006 2007
Ford Focus ST Duratec 2.3L 2005 2006 2007
Ford Focus Duratec 2.0L 2008 2009 2010 2011

Alternate SKU:
LSC304, 510 0172 10, 4B06 B a 125, 510017210, 4B06Ba125, BRG0108


Customer Reviews
5.0 Based on 7 Reviews
5 ?
100% 
7
4 ?
0% 
0
3 ?
0% 
0
2 ?
0% 
0
1 ?
0% 
0
Write a Review

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
07/20/2021
Good part

I decided to sell the car but the part overall was made pretty good.

CR
Caden R.
United States United States
07/20/2021
Works Great!

Had this installed for almost a year, works great, no noise. MAKE SURE you put a sealant around the part of this slave that mates to the transmission or you will leak transmission fluid!

TS
Thomas S.
United States United States
04/23/2021
Amazing products

So far other than slow shipping every product has been amazing, will be getting many more parts through fswerks. Car came alive with flywheel and cold air intake next up new motor...

JM
Joseph M.
United States United States
08/17/2020
Clutch release bearing on point

Have 50 miles on the new throw out bearing and have to admit compared to the other one I had the feel of this is great and no rattle noise or anything very satisfied and happy.

JG
Juan G.
United States United States
11/09/2019
2006 clutch conversion

Parts were well packed and arrived in 3 days standard ground. Quality was vastly superior to parts store replacement. 2 things of note, dowels are not installed in flywheel so you'll need a press, make sure to RTV the throw out bearing to the trans case.

CT
Conrad T.
United States United States
06/04/2019
MS
Matthew S.
United States United States
06/02/2017
Stage 1 Exedy Clutch

I now have bought 2 of these clutches and I am convinced in another 10 years I will buy another. I bought both of them from Focus Sport and I am completely satisfied with the knowledge and professional people working there.

CB
Christopher B.
United States