Cobb Accessport V3 - Ford Fiesta ST 2014-2019

SKU: AP3-FOR-001
  • $625.00
  • 4 reviews


The Accessport V3 is the industry leading OEM ECU flashing, managing and monitoring assistant. Unlock power hidden within the ECU by replacing conservative factory settings with more aggressive calibrations. The result is impressive gains in torque and horsepower while maintaining a high degree of safety. The Accessport comes with pre-installed with off-the-shelf (OTS) maps that are optimized for common performance modifications.

Flashing the factory ECU for more power is just the start of what the Accessport is capable of. The Accessport's full-color screen, intuitive interface and extensive features allow you to easily interact with your car in ways you never thought possible.

 
* 2014-2016 Fiesta ST Approved. 2017-2019 Fiesta ST Pending Approval


  Peak Gains Maximum Gains
  HP TQ HP TQ
Stage1 91 2% 19% 4% 23%
Stage1 93 2% 21% 5% 26%
Stage2 91 7% 22% 12% 27%
Stage2 93 9% 24% 14% 29%
Stage3 91 13% 33% 21% 39%
Stage3 93 15% 35% 23% 41%

Peak Gains are measured as the absolute maximum value between the highest points of two plots.
Max Gains are measured as the largest gain at a single point between the two plots.

Results may vary. Power as tested on 2014 Fiesta ST vehicles using these identical calibrations. Generally speaking, 91 octane calibrations have a richer fuel curve, and a less aggressive ignition advance map to help compensate for lower octane fuel blends such as those found in Arizona, California, and Nevada; and/or less than ideal atmospheric conditions. The maps designed for 93 octane are the most aggressive.

*91 and 93 octane results are compared against a 93 octane fuel baseline. Your 91 octane results may be higher than listed 
above; as a baseline of 91 octane fuel may read lower than our 93 octane baseline. 
*Legal only for racing vehicles which may never be used, or registered, or licensed for use upon a highway.

Non-Performance Maps

   Anti-Theft Mode v104
  • Will not allow vehicle to run
  Economy Mode v104
  • Fuel Requirements: 87 or 89 OCT (89 RON) fuel minimum
  • Intake Requirements: Stock
  • Exhaust Requirements: Stock
  • Boost Targets: Wastegate spring pressure, generally ~6psi
  • *Not intended for aggressive driving*
  Valet Mode v104
  • Fuel Requirements: 87 or 89 OCT (89 RON) fuel minimum
  • Intake Requirements: Stock
  • Exhaust Requirements: Stock 
  • Boost Targets: Stock Settings
  • Rev Limiter: 3000 RPM
  • Speed Limiter: 35mph (56.3 kph)

SIMPLE INSTALLATION:
Anyone can install the AccessPORT. No computers, wire cutting/splicing or tools of any kind are required. The AccessPORT is one of the easiest modifications you can make to your high performance vehicle. No tools are needed and no computer connection is required. Just plug the AccessPORT into the car's OBD-II port and follow the simple step-by-step on-screen instructions. In just a few minutes you will have a new performance map loaded on your ECU and be ready to experience the additional power and improved driveability of a proper tune tailored to your vehicle's modifications.

The AccessPORT comes preloaded with several performance maps for common modifications, and includes access to a free online database of additional Off-The-Shelf maps.

CHANGE MAPS:
Store up to 100 maps in the AccessPORT. Change maps whenever you want and be ready for any situation. 

The AccessPORT can store up to 100 maps so you can be ready for any situation. Use the Change Map function to browse the maps stored on the AccessPORT and select the map most appropriate for what you want to do:

Running down the drag strip to beat your last ET? Change over to your high boost map.
Heading out on a long boring highway drive? Perfect time for that fuel economy map.
Parking your car overnight in a risky area? Load the Anti-Theft map to prevent start-up. 
(for some applications)
Handing your pride and joy over to a valet for dinner?  Switch to the Valet map to limit performance.

It's like an MP3 player for your engine. The "songs" are maps and the "volume" is the throttle!

CUSTOMIZABLE MULTI-GAUGE DISPLAY:
Want Gauges? No problem. The V3 now supports up to 6 fully customizable gauges with 1/1000 resolution. Monitor all the parameters you want to see and customize each layout for street, strip or track.

GAUGES:
Monitor OEM sensor data on-the-fly. Use the AccessPORT as an additional set of gauges to monitor data directly from the ECU. 

Gauges allow you to view sensor data and calculated values in real-time right on the AccessPORT. There is no need for a clunky PC to ride shotgun with you in the passenger seat. Just plug the AccessPORT into the OBD-II port, select Live Data from the menu and choose a monitor to view. Any monitor that can be data logged can also be viewed in real time using this feature. Live Data can function as auxilliary gauges to supplement the stock gauge cluster, or it can be used to help in fine tuning custom calibrations.

Unlike dedicated auxilliary gauges that can clutter up your dashboard, the AccessPORT functions as soft gauges, allowing you to decide what gauges to display. Some examples of gauges are:

  • Throttle Position
  • Boost Pressure
  • Ignition Advance
  • Wastegate Duty Cycle
  • Mass Air Flow
  • Intake Temperature
  • Air/Fuel Ratio
  • Calculated Load
  • Vehicle Speed
  • Bypass Valve Mode
  • Coolant Temperature
  • and many more...

As you can see from this sampling, some of these monitors would be impossible to duplicate with a traditional auxilliary gauge.

DATA LOGGING:
Record multiple data channels simultaneously for in-depth evaluation of engine performance. Stores up to 10 hours. The AccessPORT functions as a hand-held data logging device. There is no need to drag your laptop computer out to the car. Just plug the AccessPORT into the OBD-II port, select Data Logging from the menu and choose which monitors you wish to data log. Choose as few or as many monitors as you like. Hit enter and data logging begins. Once the data gathering is complete, hit the enter button again. The data is stored as a data log file within the AccessPORT. The AccessPORT can store up to 10 hours of data logging.

The data logs are stored on the AccessPORT for as long as you want them there. Just unplug the AccessPORT and put it in your pocket, back-pack or briefcase. To analyze the data, simply plug the AccessPORT into any PC or Mac and download the data logs to view in your favorite spreadsheet or graphing software.

PERFORMANCE MEASURING:
Welcome to your own performance evaluation suite! Measure 0-60mph time, 60 foot and 1/4 mile ET's, and Trap Speed. 

Every AccessPORT has built in Performance Monitors. These are great for showing the performance of your vehicle in the current state of tune with the modifications you have installed as well as helping to quantify performance gains when you make additional modifications. These are also great tools to help you improve your skills at the drag strip. It's like printing off your own time slip any time you want!

The following Performance Monitors are available:

  • 60' Time: Elapsed time to 60' distance. Indicates how well your car is hooking up off the line.
  • 330' Time: Elapsed time to 330' distance
  • 0-60 mph: See where your car stacks up against the 0-60mph times published in the major car magazines.
  • 1/8 Mile: Elapsed time and vehicle speed at 1/8 mile distance (660').
  • 1000' Time: Elapsed time to 1000' distance.1/4 Mile: Elapsed time and vehicle speed at 1/4 mile distance.

REV WARNING LIGHT:
The screen of the AccessPORT will flash brightly to warn you when the engine has exceeded the limit you set. Perfect for use as a shift light! As an added bonus, the AccessPORT screen also functions as a Rev Warning Light. Simply enter the RPM you want the Rev Warning Light to activate at. The screen will brightly flash red and white to alert you when that RPM has been reached, while simultaneously showing any Live Data monitor!

TROUBLE CODES:
Read engine trouble codes to diagnose issues. Clear them when resolved. Prevent expensive trips to the dealership. 

The AccessPORT allows you to read engine codes to help troubleshoot issues and potentially save you from an expensive trip to the dealership. A brief description of the trouble code is also provided, which is handy when you don't happen to have a shop manual in your pocket.

The AccessPORT will read any trouble code reported by the ECU. In most cases this equates to hundreds of trouble codes and descriptions to help diagnose issues where ever you may be. Once the issue is resolved, the AccessPORT can be used to clear the codes to turn off the check engine light.

SIMPLE UNINSTALL:
Restore your vehicle's ECU to its original factory configuration simply by performing the Uninstall operation. In the event that the car must be returned to the stock configuration, the AccessPORT can be completely removed and the ECU restored to its factory condition. Once the AccessPORT is uninstalled, it can be installed on any vehicle the AccessPORT part number supports. Since the AccessPORT can be uninstalled, combined with the ability to update the AccessPORT firmware via the internet, it retains a high resale value.


Customer Reviews
4.8 Based on 4 Reviews
5 ★
75% 
3
4 ★
25% 
1
3 ★
0% 
0
2 ★
0% 
0
1 ★
0% 
0
Write a Review

Thank you for submitting a review!

Your input is very much appreciated. Share it with your friends so they can enjoy it too!

Filter Reviews:
01/01/2020

Nice!!

Love it running Dyno tunes from dizzy

MP
Matthew P.
United States United States
10/14/2018

My reveiw

Experience was ok. Shipping was quick and really impressed with the upgrade.

NP
Nickolaus P.
Canada
02/11/2015

Huge improvement!

I got Raffi to install it for me for the first time. Then I had to uninstall to go to the dealer. Had someone do it for me. Then I had to reinstall and was surprised at how easy it was, especially for someone like me. Will be playing with it to find out what else I can do. My car is a 2014 Fiesta ST. Thanks again Vik for recommending it.

PM
Pete M.
07/23/2014

Access the Power with the AccessPort

The AccessPort is extremely easy to install and use. It has allowed me to tap into the hidden power bands in my 2014 Ford Fiesta ST. I attached it to the left A-Pillar and ran the cable behind the paneling for a neat installation. Provides easy to read gauges in a number of out of the box layouts. Simply awesome!

MC
Mario C.